Project 240SX – Installing EVO X Brakes

This post has been moved to it’s new permanent home at My Pro Street, where they have purchased the intellectual rights to this article. If you have a how to site and want to make some spare cash check them out. Click here for the full article.

Click here for the How To upgrade your 240sx brakes

Click here for the How To upgrade your 240sx brakes

For the time being, we will be using a Centric 300zx brake master, part number 46010-30P22 for a master cylinder bore of 17/16th. However due to the ever elusive third brake fitting, we opt for a banjo bolt solution instead.

By using a m10 banjo bolt fitting, we install another Russell 65702 – banjo straight to 10mm female -3 and another Aeroquip FCM2945 – -3 male to 10mm x 1.0 inverted flare to go to the passenger side front brake.

 

17 replies
  1. Jodece mason
    Jodece mason says:

    damn, very nice set up. i’m about to put same rims on my 13 but 4 lug, and was just curious what coils you have, and if you had to raise the car for the wheels to fit. thanks

    Reply
    • stockspyder
      stockspyder says:

      I am running Megan Track Coilovers and no, no need to raise the car to clear. You will need the driver side harness lifted, but I’m sure you knew that. Thanks for chiming in!

      Reply
    • stockspyder
      stockspyder says:

      Hey Benji, you may or may not be able to run the IX calipers on a X rotor, but I was unable to on my Cryo Centric rotors, as they were oversized compared to the IX units. The skullworks bracket is steadily available, you can check places like Z1 motorsports, Enjuku or of course Pro Street Online.

      Thanks. take care and good luck on your project.

      Reply
  2. jrecord88
    jrecord88 says:

    Hi John. Where did you get the Skullworks caliper adapters from? I’ve been searching the net but can’t find them. Any help would be appreciated. Cheers from Down Under! – Josh

    Reply
    • stockspyder
      stockspyder says:

      Hey Frankie, give either of those links a call even if they arent on the website I know those skullworks brackets are sold.

      This would be a great upgrade to your Z32, these Evo Brembos really stop!

      Good luck to you and your project!

      Reply
  3. Lucio
    Lucio says:

    Hi there friends, how is the whole thing, and what you would like
    to say regarding this piece of writing, in my view its
    in fact remarkable in support of me.

    Reply
  4. Shellie
    Shellie says:

    My brother suggested I may like this blog. He was entirely right.

    This submit actually made my day. You cann’t imagine just how a lot time I had spent for this info! Thanks!

    Reply
  5. Reta
    Reta says:

    Hey there, You’ve done an excellent job. I will definitely digg it and personally suggest to my friends. I’m confident they’ll be benefited from this website.

    Reply
  6. Aracely
    Aracely says:

    I’m not that much of a internet reader to be honest but your blogs really nice, keep it
    up! I’ll go ahead and bookmark your website to come back later. All the best

    Reply

Trackbacks & Pingbacks

  1. […] I need these gone QUICK make me an offer….These are a tremendously great upgrade this guy did them and he shows you how to also Project 240SX ? Installing EVO X Brakes | StockSpyder […]

  2. […] up. With less than 30 feet between me and a large drop off into a canyon, I was reminded why I installed a set of Evolution X calipers on my […]

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *