Case Studies – Installing an HKS catback on a S13
Today we are installing an old-school HKS Hi-Power onto a 1992 Nissan 240SX SE.This is an older HKS unit with the old school dual exhaust tips, meant for NA applications. Tools you will need for this install : HKS Exhaust part number 31006-KN005 Breaker bar 14mm wrench or socket Spray on lube First raise the […]
Case Studies – 2006 Infiniti G35 Stereo Removal
This G35 has the 6 disc changer option from the factory, and it refuses to spit out discs or play discs anymore. Instead of operating, now the unit simply makes an odd buzzing sound and turns off when you attempt to access the CDs. So removing the G35 stereo is our next step, tools you […]
Case Studies – Project Supra hits the Dyno!
When we last left our 1997 Anniversary Edition Supra, it was just getting used to calling to it’s new owner and had been modded for the first time in its life. Because the car is so new, my friend is adamant about going slow and keeping it BPU for a while. He even goes so […]
Case Studies – Cam Angle Sensor and Drive Belts on a Infiniti G35
My G35 has been driven hard and put away wet by many various members of my family, and just the other day the car threw the dreaded P0340 CAS error. Oh well, I guess I can’t be too upset considering the G35 has over 230,000 miles on it. What better time to replace my drive belts […]
Case Studies – Installing a B&M Command Flo FPR in a Supercharged B series
Anthony’s Jackson Racing Supercharged EG last put down 219 hp at the wheels with a completely stock Jackson Racing setup. Since then he’s added a walbro 255HP fuel pump, which has significantly increased the fuel pressure under load. Unfortunately, it’s also wreaked havoc on his idle fuel pressure, causing an overly rich condition at idle […]
Project 383 – Installing a new fuel pump and Edelbrock 8134
After our last setback in our Project 383 where a fuel line ruptured causing a small engine fire, Butch and the gang at Treds decide to step it up a notch by installing a new fuel pump with Edelbrock’s 8134 Single Feed Fuel Line Kit. Onto the install on our carbureted Project 383, and the […]
Piggyback Heaven – Installing a VAFC in a Acura RSX
Today we’ll be installing a VTEC Air Fuel Controller part number 401-A015, otherwise known as the VAFC for this supercharged Acura RSX. Running a CT Engineering supercharger kit, but opting to leave out the programmed ECU, we’ll be installing a VAFC to round out the RSX’s fuel trims before going full blown AEM EMS standalone. Why install […]
Piggyback Heaven – Installing a SAFC in a MKIV Supra TT
I’ve died and gone to piggyback heaven in the early stages of 2012, as a good friend recently picked up a MINT 1997 Anniversary Edition Toyota Supra Turbo. I have always loved these cars and the insane amount of over-engineering that went into the legendary 2JZGTE. Since this car is probably one of the ONLY […]
Case Studies : Preparing the Talon for Dyno Day
Jesse’s Talon has come quite a ways after being cleaned up and gone through. Now all that remains is re-torquing the head studs and heading back to the dyno in our quest for 500whp. Make sure to look up your head tightening sequence to ensure you follow manufacturer guidelines. The studs we are tightening are part number […]
Case Studies – My R33 Skyline
I had my Skyline imported back in 2008 as a parts car with the original intention of following Motorex’s guidelines in federalizing the vehicle. After just 3 hours the motor and transmission was installed and within 5 the car roared to life. With a bevy of HKS parts, my Skyline belted out 365 at the […]